Universal Alternator Bracket to install Delco, Ford and Chrysler alternators in place of generators that have 2 mounting ears. Ideal for agricultural, industrial, and older vehicles. Bolts to existing 2 ear generator mounting bracket. Complete with hardware.
9N Conversion Bracket to install Delco (2" mount) alternator on tractors that have the generator on the RIGHT side. Complete with hardware.
Ford 8N Conversion Bracket to install Delco or Ford alternator on tractors that have the generator on the LEFT side, 1952 and later. Complete with hardware.
DELCO TO CHRYSLER ALTERNATOR CONVERSION BRACKET. Install DELCO alternator (2" mounting) on vehicles with CHRYSLER alternators. Complete with hardware .
DELCO TO MOTOROLA ALTERNATOR CONVERSION BRACKET. Install DELCO alternator (2" mount) on vehicles with MOTOROLA (1" mount) alternators. Complete with hardware.
BRACKET to install DELCO or FORD alternators on vehicles with "DUAL FOOT" alternators. Can be used on ARROW, COLT, COURIER, NISSAN (DATSUN), LUV, MAZDA, SUBARU, TOYOTA and industrial applications. Complete with hardware.
DELCO TO DELCO ALTERNATOR CONVERSION BRACKET. Install DELCO (2" mount) on vehicles with DELCO 27SI, TYPE 100 alternators (dual ear mounting). Complete with hardware.
UNIVERSAL WELDING BRACKET FOR DELCO ALTERNATORS. Install DELCO alternators (2" mount) with bracket that can be WELDED to customer supplied engine bracket. Un-plated for easy welding. Complete with hardware.
BRACKET for mounting "truck" type alternators with SAE 4" mounting ear spacing. Machined from mild steel to be customer WELDED to existing or custom made mounting plate. Includes grade 8 bolts.
DELCO TO FORD SPACER. Install DELCO (2" mount) alternator on FORD vehicles (3" mount). Note: mounting hole on Delco alternator must be enlarged to accept FORD 7/16" bolt.
Click here for 6 volt negative or positive ground Delco Remy Based Alternators
Click here for 8 volt and 12 volt negative or positive ground 10SI alternators
WIDE BELT PULLEY (15/32" and 1/2") for industrial and agricultural applications. 2-1/2" diameter, small enough for adequate RPM on slower speed motors, large enough for long belt life. Cold rolled steel, .670" bore for DELCO and FORD alternators.
EXTRA WIDE BELT PULLEY (5/8", 21/32", 11/16" and 3/4") for industrial and agricultural applications. 2-1/2" diameter. Cold rolled steel, .670" bore with special long neck nut.
CURVED BELT TENSION EXTENSION BRACKET. Use with alternator conversions. 1/4" thick x 1-1/4" wide curved end bar. Can be bolted or welded to existing bracket. Unplated for welding.
HEAVY DUTY CURVED BELT TENSION EXTENSION BRACKET. For "truck type" J-180 alternator installations. Heavier 3/8" thick x 1-1/4" wide curved end bar. Can be bolted or welded to existing bracket. Unplated for welding.
CURVED BELT TENSION EXTENSION BRACKET. Use with alternator conversions. 3/16" thick x 1" wide curved end bar. Can be bolted or welded to existing bracket. Unplated for welding.
UNIVERSAL BELT TENSION EXTENSION BRACKET. Use with alternator conversions. Design allows angles up to 45 degrees.
UNIVERSAL RELAY for a multitude of 12 volt applications. One normally closed contact and one normally open. POS. or NEG. ground. With connector and terminals. Similar to DELCO field relay.
UNIVERSAL IGNITION RESISTOR. Ideal for converting 6 volt vehicles to 12 volt systems. Agricultural, industrial and commercial applications. Use with universal alternator brackets.
AXIAL LEAD DIODES. Perfect for diode trio replacement.
LEECE NEVILLE "JB" ALTERNATOR WIRES. Rectifier to regulator POSITIVE and NEGATIVE connection. Like L-N 79028 and 79029. Flexible wires with TEFLON insulation, a significant improvement over OEM.
